HomeNews › New Product Roundup – October 5th

New Product Roundup – October 5th

Welcome back to a new and improved New Product Roundup! We have made a few changes based on your feedback so let us know what you think. In this first iteration of our newly updated post we have seven new products to share from a variety of different categories and a new product of the week. We also have our Toonie ‘tober $2.00 Light Packet Shipping promotion back on for the entire month of October. Let’s get to it!






New Products This Week
SEE   MORE

$4.95

4 x AA Battery Case with DC Barrel Plug

 

This battery case holds 4 AA batteries and connects them together in series. The output voltage with 4 standard AA batteries will be approximately 6VDC. The case has 220mm / 9” wire leads with a 2.1 x 5.5mm DC Barrel Jack on the end. These are ideal for use with the SparkFun moto:bit and are also compatible with our Panel Mount and Breadboard Friendly DC Barrel Jacks... [Read More]

SEE   MORE

$0.95

90mm Three Blade Propeller – Green

 

This Three Blade 90mm generic fan/propeller works great for moving air or water. Use it to build your next miniature hovercraft, boat, or just to make your DC motor less boring! The propeller is designed to fit on a 2mm shaft and will work with most small DC hobby motors we stock. Note: DC Motor Sold Separately . ... [Read More]

SEE   MORE

$10.95

IR Break Beam Sensor – 5mm LED

 

This IR break beam sensor works by detecting an object breaking a beam of IR light. This particular sensor has a range of up to 50 cm / 20". You can power it from 3.3V or 5V, but 5V will get you better range and is what we suggest. The receiver is open collector transistor output which means that you do need a pull up resistor if you want to read a digital signal off the signal wire... [Read More]

SEE   MORE

$13.95

16GB Kingston USB 3.1 Flash Drive

 

Looking to add additional storage to your Raspberry Pi 4? This fast USB 3.1 Flash drive is perfect for the new USB 3.0 capabilities of the Pi. USB 3.1 Gen 1 (USB 3.0) performance ensures quick and easy data transfer and USB 2.0 backwards compatibility means this device will work just about anywhere. DT 50 is backed by a five-year warranty from Kingston. ... [Read More]

SEE   MORE

$33.95

Anemometer – Wind Speed Sensor

 

This anemometer is the same sensor found in our Weather Meters set and can be used as a replacement part or as a stand-alone unit. These high quality weather proof sensors measure wind speed with a magnet and a reed switch. A wind speed of 2.4km/h (1.492 MPH) causes the switch to close once per second. The anemometer has a short cable terminated with a 6P2C RJ11 connector. This normally plugs into its companion wind vane – but it can also be connected to an RJ11 Breakout Board and hooked up on its own... [Read More]

SEE   MORE

$10.95

Raspberry Pi 4 Case – Black

 

This case is designed to fit the all-new Raspberry Pi 4. It works with all three variations of the Pi 4 and provides a decent amount of ventilation. The case is comprised of three pieces – a base, midsection, and a lid. With the lid removed, there is also a small slot that the camera can be slid into... [Read More]

SEE   MORE

$3.95

RJ15 Breakout Board

 

Cable terminated with an RJ11 can be quite hard to work with. The narrow pins are very hard to make contact with on their own and the mating connectors are not breadboard compatible. This RJ11 breakout solves the problem! The simple board breaks out all 6 conductors to a breadboard compatible header. This board is ideal for our Weather Meters and can be used to connect these sensors to breadboards and perfboards with ease! Each breakout board ships with the RJ11 connector soldered in place and a small chunk of breakaway header that can be soldered on if desired.... [Read More]

Feature Products
Product Of The Week - 50 Off

$3.95

Ultrabright Cool White LED

 

  This week we have Ultrabright Cool White LED featured as our Product of the Week. This item is on sale for 50 OFF until Friday at midnight Pacific time - so do not miss out!

Current Promotions
 


Latest Tutorial

Getting Started With The ultrasonic:bit For BBC micro:bit

The ultrasonic:bit takes all of the complicated wiring out of using an ultrasonic distance sensor with the micro:bit. In this tutorial we look at how to set one up with the BBC micro:bit and measure distance. Interested? Head on over to the tutorial!

Tags:

Leave a Reply