HomeNews › New Product Roundup – February 1st

New Product Roundup – February 1st

We are back for the first New Product Roundup of February! This week we have seven new products to share and a new Product Of The Week at 50% Off. Also, with the start of the new month, we have a new shipping promotion! Our $2.00 Light Packet Shipping is back for all light packet orders in Canada. For more information on the shipping promotion check out our post. With that out of the way, let’s get to the new stuff!






New Products This Week
SEE   MORE

$3.95

GT2 Idler Pulley – 16 Tooth 3mm Bore

 

This GT2 timing pully has 16 teeth and is designed to be an idler in a belt system. Unlike a standard GT2 pulley, this one has a set of bearings pressed into the center bore. The bearings have a center bore of 3mm and allow the pulley to spin freely on a stationary shaft or bolt. The pully is designed to work with all forms of 6mm wide GT2 belt we carry in stock... [Read More]

SEE   MORE

$9.95

N20 Micro Gear Motor – 6V 300RPM

 

This N20 gearmotor is a miniature DC motor with integrated gearbox. The gearbox allows a much lower output shaft speed and greater torque from this tiny motor. We carry several versions of this motor with different output shaft speeds and input voltages. This specific model is 6V and approximately 300 RPM. The output is a 3mm diameter flatted shaft and is compatible with our 43mm Wheel as well as any 3mm shaft couplers and adapter hubs... [Read More]

SEE   MORE

$9.95

N20 Micro Gear Motor – 6V 100RPM

 

This N20 gearmotor is a miniature DC motor with integrated gearbox. The gearbox allows a much lower output shaft speed and greater torque from this tiny motor. We carry several versions of this motor with different output shaft speeds and input voltages. This specific model is 6V and approximately 100 RPM. The output is a 3mm diameter flatted shaft and is compatible with our 43mm Wheel as well as any 3mm shaft couplers and adapter hubs... [Read More]

SEE   MORE

$0.50

Vibration Switch – SW-520D

 

A vibration sensor is a simple, low cost, way to detect vibration or tilt in a specific direction. They are not sophisticated enough to tell you the direction of movement – just that there has been some sort of tilting or vibration. Tilting the sensor or exposing it to higher vibration will cause the metal ball inside to create a connection between the two pins, effectively working like a switch. These are not designed for high voltage or high current and should be kept to 12VDC / 20mA or less... [Read More]

SEE   MORE

$37.95

Adafruit Feather nRF52840 Express

 

The Adafruit Feather nRF52840 Express features Bluetooth Low Energy, built in battery charging, and native USB support. This chip has twice the flash, and four times the SRAM of it's earlier sibling, the nRF52832 - 1 MB of FLASH and 256KB of SRAM. Compared to the nRF51, this board has 4-8 times more of everything. For this chip, Adafruit has added Arduino IDE support - you can program the nRF52840 chip directly to take full advantage of the Cortex-M4 processor, and then calling into the Nordic SoftDevice radio stack when you need to communicate over BLE. Adafruit has also picked this chip for their first BLE-friendly CircuitPython board! CircuitPython works best with disk drive access, and this is the only BLE-plus-USB-native chip that has the memory to handle running a the little Python interpreter... [Read More]

SEE   MORE

$22.95

MPRLS Ported Pressure Sensor – 0 to 25 PSI

 

This pressure sensor is designed to work between 0 and 25PSI and features a metal port. This is ideally suited for assistive tech such as “Sip & Puff” interfaces, measuring pressure in closed spaces, or pressurized systems. Since the sensor ranges from 0 to 25 PSI, it has fairly decent range above and below ambient sea level pressure of roughly 14.5 psi. The sensor itself is comprised of a silicone-gel covered pressure sensing gauge with a 2.5mm diameter metal port measuring 3.7mm long... [Read More]

SEE   MORE

$16.95

2.4GHz Dipole Swivel Antenna with RP-SMA – 16dBi

 

External antennas can make a world of difference in wireless applications! This giant 2.4 - 2.5 GHz antenna is approximately 390mm long and provides an additional 16dBi of gain. The Antenna itself has a swivel base and an RP-SMA connector. To connect to a smaller uFL connector we recommend picking up a RP-SMA to uFL Adapter Cable as well. ... [Read More]

Feature Products
Product Of The Week - 50% Off

$4.95

7-Segment Display – Red

 

  This week we have 7-Segment Display – Red featured as our Product of the Week. This item is on sale for 50% OFF until Friday at midnight Pacific time - so do not miss out!

Current Promotions
 

Latest Tutorial

Sending An Email With Attached Photo Using Python And The Raspberry Pi

We have already covered using a Raspberry Pi and Python to send an email containing basic text – but what if you wanted to attach a picture instead? In this tutorial we are going to adapt our code from our basic email tutorial to allow picture attachments to be sent. Interested? Head on over to the tutorial!

Tags:

Leave a Reply