HomeNews › New Product Roundup – January 4th

New Product Roundup – January 4th

Welcome back to the first New Product Roundup of 2020! Now that the holidays are over, everything is starting to get back to normal. With that, we have 3 new products and 2 updated products to share this week along with a new Product Of The Week at 20% Off!

New Products This Week


Insulated Silicone Soldering & Rework Mat


Stop melting your desk and searing your workbench! This silicone mat is made of 4mm thick rubber and can take just about anything you throw at it. It's stable, strong, non-slip, non-conductive and heat-resistant surface for your workstation. It's also skid resistant! The silicone is just soft enough with some grip that it doesn't slide around, and PCBs will stay in place. The heat insulation increases soldering efficiency and keeps whatever you're working on safely in one spot. You can use hot air, soldering irons, etc without damage to either the mat or iron... [Read More]



Adafruit Feather M0 Adalogger


The Feather M0 Adalogger is an all-in-one microcontroller, datalogger, and battery charger. The Adafruit designed board features a powerful processor, integrated battery charger, and microSD slot. At the Feather M0's heart is an ATSAMD21G18 ARM Cortex M0 processor, clocked at 48 MHz and at 3.3V logic. This chip has a whopping 256K of FLASH (8x more than the Atmega328 or 32u4) and 32K of RAM (16x as much)! This chip comes with built in USB so it has USB-to-Serial program & debug capability built in with no need for an FTDI-like chip. To make it easy to use for portable projects, Adafruit has added a JST connector for their 3.7V Lithium polymer batteries and built in battery charging... [Read More]



9V Battery Case – Switch


This battery case is for use with 9V batteries and features an on off switch and a 2.1mm DC barrel jack. The "center pin" of the DC barrel jack is positive and the outer barrel is negative meaning it is compatible with Arduino's DC barrel plugs. The battery snaps nicely into the connector and is fully enclosed inside of the case. There are no mounting holes on this case, but a strong double sided tape could be used to mount it to your project... [Read More]



Solder Wire Holder Stand – TJ-227


A soldering iron stand is a must for any well set up electronics workstation. This well built metal stand from Atten holds up to 1kg spools of solder and keeps it from getting tangled. The stand ships fully assembled and works with all solder spools we stock. ... [Read More]



Adafruit DC Motor + Stepper FeatherWing


This is the Adafruit DC Motor + Stepper FeatherWing – a board designed to let you use 2 x bi-polar stepper motors or 4 x brushed DC motors (or 1 stepper and 2 DC motors) with any of the Adafruit Feather series of microcontrollers. This is effectively the Adafruit Motor Shield squished down to fit in a Feather form factor – ideal for smaller, portable projects. Since this FeatherWing only uses I2C (SDA & SCL pins), it can be stacked with any other FeatherWing or with itself (just make sure you have each wing with a unique I2C address). There are 5 address-select jumper pads on the back of the board - means up to 32 stackable wings: that's 64 steppers or 128 DC motors! Instead of using a latch and the Arduino's PWM pins, we have a fully-dedicated PWM driver chip onboard... [Read More]

Feature Products
Product Of The Week - 20% Off


USB 3.0 to SATA Adapter Cable


  This week we have USB 3.0 to SATA Adapter Cable featured as our Product of the Week. This item is on sale for 20% OFF until Friday at midnight Pacific time - so do not miss out!

Current Promotions

Latest Tutorial

Sending An Email With Attached Photo Using Python And The Raspberry Pi

We have already covered using a Raspberry Pi and Python to send an email containing basic text – but what if you wanted to attach a picture instead? In this tutorial we are going to adapt our code from our basic email tutorial to allow picture attachments to be sent. Interested? Head on over to the tutorial!


Leave a Reply